LIFTY // JOURNAL
KuKirin Error Codes by Model: G2, G2 Pro, G2 Max, G2 Master, G3, G4 (Official List)
Safety before troubleshooting
If a battery, charger or wiring is wet, damaged, swollen, unusually hot, smells abnormal or shows signs of burning, stop use and charging and obtain appropriate professional advice. Do not charge simply to clear a code in those circumstances. Never open a battery, bypass a safety device or swap live connectors. The tables identify manufacturer-published meanings; parts replacement requires diagnosis.
Record the complete code and exact model and check the supplied manual. Use the linked manufacturer list as the source; code meanings can change by display and revision.
KuKirin error codes are not the same on every model. An "E-2" on a G2 means under-voltage, but "E-002" on a G2 Pro means a throttle fault. This guide lists each code exactly as KuKirin publishes it, grouped by model, so you can match the code to your own scooter. Lifty Electric sells and services KuKirin scooters at its own workshop, 157 Capel Street, Dublin 1.
Quick answer: first identify your exact model and how the code is shown. Older G2, G3 and G4 displays use single digits (E-0 to E-7: E-2 under-voltage, E-4 throttle, E-5 brake, E-6 communication, E-7 Hall sensor). The G2 Pro, G2 Max, G2 Master, G3 Pro and G4 Max use three digits (E-001 Hall sensor, E-002 throttle, E-003 controller, E-005 under-voltage, E-006/E-007 display communication, E-009 controller overheating). The G2 Ultra, A1 and M4 Max each have their own list below. If a code persists, have it diagnosed before riding. Do not charge damaged, wet or unusually hot equipment to try to clear a code.
Source and limits. Every meaning below comes from KuKirin's own published list, Error Codes List for KuKirin Electric Scooter (KuKirin, updated 31 December 2025), checked by Lifty Electric on 15 November 2026. KuKirin’s repair instructions are written for technicians; this page lists meanings and conservative owner checks. The manual supplied with your scooter takes priority: displays and firmware differ between production years. A code points to a circuit; it does not prove which part has failed. That needs testing.
Step 1: identify your model and code style
- Single digit (E-0 to E-7, or "88"): earlier KuKirin G2, G3 and G4. Jump to the table.
- Three digits, single motor: G2 Pro, G2 Max. Jump to the table.
- Three digits, dual motor: G2 Master, G3 Pro, G4 Max (front-motor codes start E-01x). Jump to the table.
- G2 Ultra, A1, M4 Max: separate lists. G2 Ultra · A1 · M4 Max.
Not sure which you have? The model is printed on the stem or the deck label. If your display shows a code that is not in these lists (for example on a 2026 G2 or G4 with a newer display), treat it as unconfirmed and check the manual or contact us before replacing parts.
KuKirin error codes by model
KuKirin G2, G3 and G4 (single-digit codes E-0 to E-7)
| Code | KuKirin's meaning |
|---|---|
| E-0 | Stalling fault |
| E-1 | Over-voltage fault |
| E-2 | Under-voltage fault |
| E-3 | Controller fault |
| E-4 | Throttle fault |
| E-5 | Brake fault |
| E-6 | Serial communication fault |
| E-7 | Hall sensor fault |
| 88 | "88" shown on a G2 display |
KuKirin G2 Pro and G2 Max (three-digit codes)
| Code | KuKirin's meaning |
|---|---|
| E-001 | Hall sensor fault |
| E-002 | Throttle fault |
| E-003 | Controller fault |
| E-005 | Battery under-voltage |
| E-006 | Display (instrument) receiving fault |
| E-007 | Display (instrument) sending fault |
| E-009 | Controller over-temperature |
KuKirin G2 Master, G3 Pro and G4 Max (dual motor, three-digit codes)
| Code | KuKirin's meaning |
|---|---|
| E-001 | Rear motor Hall sensor fault |
| E-002 | Throttle fault |
| E-003 | Rear controller fault |
| E-005 | Rear battery under-voltage |
| E-006 | Display receiving fault |
| E-007 | Display sending fault |
| E-009 | Rear controller over-temperature |
| E-011 | Front motor Hall sensor fault |
| E-013 | Front controller fault |
| E-015 | Front battery under-voltage |
| E-017 | Front controller receiving fault |
| E-019 | Front controller over-temperature |
KuKirin G2 Ultra
| Code | KuKirin's meaning |
|---|---|
| E-000 | Motor stall / locked rotor |
| E-001 | Battery over-voltage |
| E-002 | Battery under-voltage |
| E-003 | Controller failure |
| E-004 | Throttle error |
| E-005 | Brake lever error |
| E-006 | Communication failure |
| E-007 | Rear motor Hall error |
| E-008 | Front motor Hall error |
| E-009 | Battery communication failure |
KuKirin A1
| Code | KuKirin's meaning |
|---|---|
| E-001 | Rear motor failure |
| E-002 | Throttle error |
| E-003 | Controller failure |
| E-004 | Brake failure |
| E-005 | Battery under-voltage |
| E-006 | Display receiving error |
| E-007 | Display sending error |
| E-008 | Motor overheating |
| E-009 | Controller overheating |
KuKirin M4 Max
| Code | KuKirin's meaning |
|---|---|
| E-01 | Motor failure |
| E-02 | Throttle failure |
| E-03 | Controller failure |
| E-05 | Battery under-voltage |
| E-06 | Communication failure (display) |
| E-07 | Communication failure (controller) |
| E-09 | Motor overheating |
Codes as published by KuKirin (31 December 2025). Codes missing from a list (for example E-004 or E-008 on the G2 Pro) are not published by KuKirin for that model.
Safe checks you can do at home
- Record the fault first. Follow the exact manual. Do not restart or charge equipment when water ingress or damage is suspected.
- For an under-voltage indication, first check the supplied manual and rule out damage or moisture. Charge only when the battery and charger are safe, compatible and within their permitted conditions. A persistent code requires diagnosis.
- Check both brake levers spring back fully for brake codes (E-5, E-004 on the A1, E-005 on the G2 Ultra).
- Let it cool for over-temperature codes (E-009, E-019, E-008/E-009 on the A1).
- Look, don't open: check the folding stem for a pinched cable (communication codes) and the motor cable at the wheel for cuts.
Leave to a workshop: opening the deck, swapping motor plugs, reconnecting the main harness, service-software resets and anything inside the battery. Never bypass a brake sensor. Don't ride with a Hall sensor, motor, controller or communication code: power can cut out or the motor can stall without warning.
Why we rewrote this guide
An earlier version of this page (24 October 2026) used one generic E01–E10 table for all KuKirin models. That table didn't match KuKirin's published codes, and it disagreed with our error code database. On 15 November 2026 we replaced the generic table with model-specific information and changed the database into a source directory. See our editorial standards for how we correct pages.
KuKirin repair in Dublin
Bring your KuKirin to 157 Capel Street, Dublin 1 (near Jervis Luas). Repairs are by booking only: Tuesday to Friday 11:30–18:00 and Saturday 11:30–17:00. Electrical diagnostics cost €49.99 for single-motor scooters and €69.99 for dual-motor models such as the G2 Master and G4 Max. We tell you the fault and the repair price before any work starts. Puncture repair is €59 and brake pad replacement starts at €50. See all repair prices, or find the shop.
Shopping for a KuKirin? Compare every model on our KuKirin Ireland page, or read KuKirin G2 Master vs G4. Only scooters meeting 20 km/h, 400W continuous rated power and a maximum of 25 kg can be used on Irish public roads, so most KuKirin models are for private land only. Check yours with our free e-scooter law checker. For other brands, see Xiaomi, Segway, NAMI and Dualtron error codes.
KuKirin error code FAQs
What does E-6 or E-006 mean on a KuKirin scooter?
On G2, G3 and G4 scooters with single-digit codes, E-6 is a serial communication fault, usually the main harness (often pinched in the folding stem). On the G2 Pro, G2 Max, G2 Master, G3 Pro and G4 Max, E-006 is a display (instrument) receiving fault. Both are communication problems between the display and the controller.
Why does E-2 mean something different on my G2 Pro?
KuKirin uses different code lists. On older single-digit displays E-2 is under-voltage; on the three-digit G2 Pro and G2 Max, E-002 is a throttle fault. Always use the list for your exact model.
How do I reset a KuKirin error code?
Record the exact model and complete code and check the supplied manual. Do not repeatedly reset a persistent fault. Do not charge or use equipment that may be damaged, wet, swollen or unusually hot; arrange professional diagnosis.
Is it safe to ride with a KuKirin error code?
Stop riding when power delivery, steering or braking is unreliable. A fault code alone does not prove which component has failed. Do not charge equipment with suspected battery damage or water ingress; seek appropriate professional advice.
How much does KuKirin repair cost in Dublin?
At Lifty Electric's workshop on Capel Street, diagnostics cost €49.99 for single-motor scooters and €69.99 for dual-motor models. Puncture repair is €59 and brake pad replacement starts at €50. Parts are quoted after inspection. Repairs are by booking only.
More diagnostic tools
Related guide: Which KuKirin G2 to buy: G2, G2 Pro, G2 Max, G2 Ultra or G2 Master
Related guide: Kugoo scooters Ireland: Kugoo vs KuKirin explained
Ready to compare models? See all the electric scooters we sell in Ireland, with current prices, set up by our own workshop at 157 Capel Street, Dublin 1, and delivered nationwide.
Need it fixed? Book electric scooter repairs in Dublin at our Capel Street workshop (booking required, Tue–Fri 11:30–18:00, Sat 11:30–17:00).
